Wall Cladding / Siding
Table of contents
Benefits
- Excellent investment for your project (Increases the value of your home)
- Replaces the use of natural wood, avoiding the distruction of forests.
- Reduces pollution from bottles, bags and other plastic products.
- Is made from recycled materials and is 100% recyclable.
- Long lasting product that resists outdoor conditions and UV rays.
- Resistant to enviromental humidity and rain (does not rot)
- Resistant to fungi and insects.
- Does not spread fire
- Easy to install.
- Excellent warranty.
- Only requires occasional cleaning (Water and soap).
Features
*Colors that are normally available in stock: Dark Brown and Teak.
*Other colors may be available. (Talk to our specialist)
Click to enlarge the images:
Accessories
Note: Plastic Posts can be replaced by an aluminum frame such as the one used to support lightweight or gypsum walls.
Gallery
Technical Information
Certifications
ISO 9001:2015 Quality Management System / (Design, Development and Production).
ISO 14001:2015 Environmental Management System / (Design, Development and Production).
GB/T24001-2004 Environmental Management System / (Design, Development and Production).
BSCI Supply Chain Management System / (Social Compliance).
CE (Conformité Européenne) / (Health, safety and environmental protection).
RoHS Directive 2002/95/EC / (Meets Restriction of Hazardous Substances).
FSC (Forest Stewardship Council) / (Recycled raw materials derived from sustainable sources).
Supplier Certification Audited by (SGS/Bureau Veritas) / (Documentation, certifications, and products).
Click to enlarge the images:
Installation
1. Storage
Before installing your ECO-SIDING, store the boards by laying them on a smooth, flat surface and do not leave them exposed to the sun. Ideally, store the material near the installation site for at least 24 hours prior to installation to allow it to get adapted to environmental conditions of the area.
2. Support Surface
The ECO-SIDING must be attached to a support structure (furring profile or plastic posts).
Joints (Expansion and Contraction)
Like other construction products, the ECO-SIDING boards will expand and contract with temperature changes. For this reason it is important to leave and adequate space between the boards. Follow the guidelines provided in the Expansion table (See section “Expansion Table” below).
In hot locations, the ECO-SIDING boards should be cut in the shade and as early as possible during the day, to prevent them from heating up and expanding. If the boards are cut after exposure to the heat or sun, this can cause problems after the product has been installed and the spacing or gap between board ends will end up being larger than they should be.
Additionally, note that when placing the ends of the boards against rigid elements such as walls; a distance of 1cm should be left between the end of each board and that particular element (For example: wall) The boards should never be glued on to each other.
*Failure to follow any basic installation standard or recommendation will void the limited warranty.
1) Center and screw the (Metallic) Starter Clip on to the keel. (Leave a gap of at least 1cm between the head or end of the keel and any vertical element (walls, gates, entrances, etc.).
2) Repeat procedure 1 on each keel. (All keels must have a Starter Clip to hold the board).
3) Position and fit the side slot of the first board to the lip of the Starting Clips.
Once the first siding board is hooked up properly on to the starter clips, screw the top tab of the siding board on to the post to properly fasten the board to the frame.
The gap space that should be left at the end of each board where two boards meet can vary. To determine the correct spacing to be used, the Expansion Table shown below must be followed. The table indicates the distance (in millimeters) that must be left between board ends (according to the length of the boards) and the "Delta T" (or difference between ambient temperatures) between the day of installation and the highest temperature that can be reached in that particular location
Example: If 2.20 meter boards are installed in a day where the ambient temperature is 20°C and they are being installed in a place where the maximum possible temperature can reach 40°C (the Delta T or temperature difference is 20°C). Therefore, a distance or gap of approximately 6mm should be left between the ends of the boards.
Maintenance
To properly maintain your ECO-SIDING, follow these steps:
- Clean your ECO-SIDING wall periodically (as required).
- You can use a soft root brush and soap and water.
- If you use a pressure washer, make sure you stay at least 50cm away form the boards to avoid damaging them.
Warranty
English 
Spanish